[cisco-voip] Caller ID on MGCP FXS Port

Discussion:

Court Schuett

2005-02-08 20:37:52 UTC

Hello,

I've got a Gold Fax fax server set up to run off of 4 FXS ports on an
ICS. I have two small hunt groups set up to handle the inbound calls but
I'm having trouble passing the caller id information into the fax lines.

What I would like to do is this:
HP: 7060 -> hunt group that routes to FaxModem1 on server and passes a
predetermined number (it can really be anything) to the fax server.
HP: 7050 -> hunt group that routes to FaxModem2-4 on server and passes a
different predetermined number.

I have almost everything set up. I have both hunt groups set up and
working correctly. 7060 is ringing to the correct modem, and 7050 is
ringing to all three modems (longest idle) correctly. The only problem
is that I can't seem to pass any sort of caller id to the FXS ports.
I've hooked up a regular analog phone and it's not getting anything
either. The CCM is connected to the FXS ports with MGCP.

CCM: 4.0(1)sr2a
HW: ICS7750-MRP300 (MPC860P)
SW: 12.3(2)XA

Any ideas?

Thanks.

Wes Sisk

2005-02-08 19:42:51 UTC

Permalink

analog mgcp does not yet support callerid, you will need to use h323.

/Wes

Post by Court Schuett
Hello,
I've got a Gold Fax fax server set up to run off of 4 FXS ports on an
ICS. I have two small hunt groups set up to handle the inbound calls but
I'm having trouble passing the caller id information into the fax lines.
HP: 7060 -> hunt group that routes to FaxModem1 on server and passes a
predetermined number (it can really be anything) to the fax server.
HP: 7050 -> hunt group that routes to FaxModem2-4 on server and passes a
different predetermined number.
I have almost everything set up. I have both hunt groups set up and
working correctly. 7060 is ringing to the correct modem, and 7050 is
ringing to all three modems (longest idle) correctly. The only problem
is that I can't seem to pass any sort of caller id to the FXS ports.
I've hooked up a regular analog phone and it's not getting anything
either. The CCM is connected to the FXS ports with MGCP.
CCM: 4.0(1)sr2a
HW: ICS7750-MRP300 (MPC860P)
SW: 12.3(2)XA
Any ideas?
Thanks.
_______________________________________________
cisco-voip mailing list
https://puck.nether.net/mailman/listinfo/cisco-voip

Walenta, Phil

2005-02-08 20:45:21 UTC

Permalink

I don't remember the ICS supporting any sort of caller ID off of its
ports.

If you can get your hands on an ATA or other gateway, you could test
with those.

I'd also recommend getting of the ICS entirely (due to end of sale etc),
I've never had good luck getting that platform to do much of anything.

-----Original Message-----
From: cisco-voip-***@puck.nether.net
[mailto:cisco-voip-***@puck.nether.net] On Behalf Of Court Schuett
Sent: Tuesday, February 08, 2005 2:38 PM
To: cisco-***@puck.nether.net
Subject: [cisco-voip] Caller ID on MGCP FXS Port

Hello,

I've got a Gold Fax fax server set up to run off of 4 FXS ports on an
ICS. I have two small hunt groups set up to handle the inbound calls but
I'm having trouble passing the caller id information into the fax lines.

What I would like to do is this:
HP: 7060 -> hunt group that routes to FaxModem1 on server and passes a
predetermined number (it can really be anything) to the fax server.
HP: 7050 -> hunt group that routes to FaxModem2-4 on server and passes a
different predetermined number.

I have almost everything set up. I have both hunt groups set up and
working correctly. 7060 is ringing to the correct modem, and 7050 is
ringing to all three modems (longest idle) correctly. The only problem
is that I can't seem to pass any sort of caller id to the FXS ports.
I've hooked up a regular analog phone and it's not getting anything
either. The CCM is connected to the FXS ports with MGCP.

CCM: 4.0(1)sr2a
HW: ICS7750-MRP300 (MPC860P)
SW: 12.3(2)XA

Any ideas?

Thanks.

Court Schuett

2005-02-08 21:10:23 UTC

Permalink

If that is the case, is there any way to do hunt groups off of H323? I
put in a TAC case the other day and they recommended I go MGCP. When I
tried to do it with H323 (that's the way it was initially) when I tried
to do a hunt group, it just went to busy because it couldn't find any of
the numbers in the hunt group.

Thanks

-Court

-----Original Message-----
From: Wes Sisk [mailto:***@cisco.com]
Sent: Tuesday, February 08, 2005 1:43 PM
To: Court Schuett
Cc: cisco-***@puck.nether.net
Subject: Re: [cisco-voip] Caller ID on MGCP FXS Port

analog mgcp does not yet support callerid, you will need to use h323.

/Wes

Post by Court Schuett
Hello,
I've got a Gold Fax fax server set up to run off of 4 FXS ports on an
ICS. I have two small hunt groups set up to handle the inbound calls

but

Post by Court Schuett
I'm having trouble passing the caller id information into the fax

lines.

Post by Court Schuett
HP: 7060 -> hunt group that routes to FaxModem1 on server and passes a
predetermined number (it can really be anything) to the fax server.
HP: 7050 -> hunt group that routes to FaxModem2-4 on server and passes

Post by Court Schuett
different predetermined number.
I have almost everything set up. I have both hunt groups set up and
working correctly. 7060 is ringing to the correct modem, and 7050 is
ringing to all three modems (longest idle) correctly. The only problem
is that I can't seem to pass any sort of caller id to the FXS ports.
I've hooked up a regular analog phone and it's not getting anything
either. The CCM is connected to the FXS ports with MGCP.
CCM: 4.0(1)sr2a
HW: ICS7750-MRP300 (MPC860P)
SW: 12.3(2)XA
Any ideas?
Thanks.
_______________________________________________
cisco-voip mailing list
https://puck.nether.net/mailman/listinfo/cisco-voip

Wes Sisk

2005-02-08 20:24:21 UTC

Permalink

Hi Court,

Yes, it is possible to implement a hunt group in h323 configuration by
using multiple pots peers with the same destination pattern and varying
'preference'

dial-peer voice 1 pots
destination-pattern 20..
port 0/0
preference 0
prefix ,,,,
dial-peer voice 2 pots
destination-pattern 20..
port 0/1
preference 1
prefix ,,,,
(etc.)

Remember that on POTS dial-peers any digits not explicitly matched are
pulsed out of the port as DTMF. So in the above example, if the CM
sends an h323 call setup to the MRP with calledpartynumber=2045 the call
will route to port 0/0. The MRP will supply ring voltage down the line
and then 4 seconds later (4 commas) it will pulse out the digits 4 5.
All the normal h323 dial-peer configurations are still needed.
Supplimentary info:
http://www.cisco.com/en/US/partner/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml
http://www.cisco.com/en/US/partner/tech/tk652/tk90/technologies_tech_note09186a0080147524.shtml

/Wes

/Wes

Post by Court Schuett
If that is the case, is there any way to do hunt groups off of H323? I
put in a TAC case the other day and they recommended I go MGCP. When I
tried to do it with H323 (that's the way it was initially) when I tried
to do a hunt group, it just went to busy because it couldn't find any of
the numbers in the hunt group.
Thanks
-Court
-----Original Message-----
Sent: Tuesday, February 08, 2005 1:43 PM
To: Court Schuett
Subject: Re: [cisco-voip] Caller ID on MGCP FXS Port
analog mgcp does not yet support callerid, you will need to use h323.
/Wes

Post by Court Schuett
Hello,
I've got a Gold Fax fax server set up to run off of 4 FXS ports on an
ICS. I have two small hunt groups set up to handle the inbound calls

but

Post by Court Schuett
I'm having trouble passing the caller id information into the fax

lines.

p***@us.army.mil

2005-02-08 23:05:37 UTC

Permalink

you should be able to also assign the voice-ports to a trunk group then point one dialpeer to the respective trunk group wrather than creating several dial-peers. I used that with FXOs and it worked great.

V/R,
PETER CASANAVE
SFC, USA
BBN Platoon Sergeant

----- Original Message -----
From: Wes Sisk <***@cisco.com>
Date: Tuesday, February 8, 2005 2:24 pm
Subject: Re: [cisco-voip] Caller ID on MGCP FXS Port

Post by Wes Sisk
Hi Court,
Yes, it is possible to implement a hunt group in h323
configuration by
using multiple pots peers with the same destination pattern and
varying
'preference'
dial-peer voice 1 pots
destination-pattern 20..
port 0/0
preference 0
prefix ,,,,
dial-peer voice 2 pots
destination-pattern 20..
port 0/1
preference 1
prefix ,,,,
(etc.)
Remember that on POTS dial-peers any digits not explicitly matched
are
pulsed out of the port as DTMF. So in the above example, if the
CM
sends an h323 call setup to the MRP with calledpartynumber=2045
the call
will route to port 0/0. The MRP will supply ring voltage down the
line
and then 4 seconds later (4 commas) it will pulse out the digits 4
5.
All the normal h323 dial-peer configurations are still needed.
http://www.cisco.com/en/US/partner/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml
http://www.cisco.com/en/US/partner/tech/tk652/tk90/technologies_tech_note09186a0080147524.shtml
/Wes
/Wes

Post by Court Schuett
If that is the case, is there any way to do hunt groups off of

H323? I

Post by Court Schuett
put in a TAC case the other day and they recommended I go MGCP.

When I

Post by Court Schuett
tried to do it with H323 (that's the way it was initially) when I

tried>to do a hunt group, it just went to busy because it couldn't
find any of

Post by Court Schuett
the numbers in the hunt group.
Thanks
-Court
-----Original Message-----
Sent: Tuesday, February 08, 2005 1:43 PM
To: Court Schuett
Subject: Re: [cisco-voip] Caller ID on MGCP FXS Port
analog mgcp does not yet support callerid, you will need to use h323.
/Wes

Post by Court Schuett
Hello,
I've got a Gold Fax fax server set up to run off of 4 FXS ports

on an

Post by Court Schuett

Post by Court Schuett
ICS. I have two small hunt groups set up to handle the inbound calls

but

Post by Court Schuett
I'm having trouble passing the caller id information into the fax

lines.

Post by Court Schuett
HP: 7060 -> hunt group that routes to FaxModem1 on server and

passes a

Post by Court Schuett

Post by Court Schuett
predetermined number (it can really be anything) to the fax server.
HP: 7050 -> hunt group that routes to FaxModem2-4 on server and

passes>>

Post by Court Schuett
a

Post by Court Schuett
different predetermined number.
I have almost everything set up. I have both hunt groups set up and
working correctly. 7060 is ringing to the correct modem, and

7050 is

Post by Court Schuett

Post by Court Schuett
ringing to all three modems (longest idle) correctly. The only

problem>>is that I can't seem to pass any sort of caller id to the
FXS ports.

Post by Court Schuett

Post by Court Schuett
I've hooked up a regular analog phone and it's not getting anything
either. The CCM is connected to the FXS ports with MGCP.
CCM: 4.0(1)sr2a
HW: ICS7750-MRP300 (MPC860P)
SW: 12.3(2)XA
Any ideas?
Thanks.
_______________________________________________
cisco-voip mailing list
https://puck.nether.net/mailman/listinfo/cisco-voip

_______________________________________________
cisco-voip mailing list
https://puck.nether.net/mailman/listinfo/cisco-voip

Court Schuett

2005-02-08 23:24:15 UTC

Permalink

Thanks for the help. That did the trick. I didn't even think of that.
I was trying to do the hunting on the Call Manager instead of the
gateway.

Thanks

-Court

-----Original Message-----
From: Wes Sisk [mailto:***@cisco.com]
Sent: Tuesday, February 08, 2005 2:24 PM
To: Court Schuett
Cc: cisco-***@puck.nether.net
Subject: Re: [cisco-voip] Caller ID on MGCP FXS Port

Hi Court,

Yes, it is possible to implement a hunt group in h323 configuration by
using multiple pots peers with the same destination pattern and varying
'preference'

dial-peer voice 1 pots
destination-pattern 20..
port 0/0
preference 0
prefix ,,,,
dial-peer voice 2 pots
destination-pattern 20..
port 0/1
preference 1
prefix ,,,,
(etc.)

Remember that on POTS dial-peers any digits not explicitly matched are
pulsed out of the port as DTMF. So in the above example, if the CM
sends an h323 call setup to the MRP with calledpartynumber=2045 the call

will route to port 0/0. The MRP will supply ring voltage down the line
and then 4 seconds later (4 commas) it will pulse out the digits 4 5.
All the normal h323 dial-peer configurations are still needed.
Supplimentary info:
http://www.cisco.com/en/US/partner/tech/tk652/tk90/technologies_tech_not
e09186a008010fed1.shtml
http://www.cisco.com/en/US/partner/tech/tk652/tk90/technologies_tech_not
e09186a0080147524.shtml

/Wes

/Wes

Post by Court Schuett
Hello,
I've got a Gold Fax fax server set up to run off of 4 FXS ports on an
ICS. I have two small hunt groups set up to handle the inbound calls

but

Post by Court Schuett
I'm having trouble passing the caller id information into the fax

lines.